Alinco DR-592T Installationshandbuch PDF herunterladen

TGR-SL-USB

SignaLink USB

Cable List - Rev 48

Last Update - 24 December 2013

Last Tigertronics Update - 15 November 2013

Tigertronics SignaLink USB Digital Interface - Cable

Interface Listing

SignaLink Jumper Settings & Wiring Information For Base & Mobile Radios

References to other non-USB models have been removed from the original Tigertronics document.

Warning: Tigertronics has not verified the accuracy of all of the radio wiring information that is provided here. This

information is provided for reference only and is NOT intended to replace the jumper installation procedure in the

“Connecting The Radio” section of the SignaLink Installation Manual. It is essential that you double-check this information

against your radio's manual before doing the actual installation. While it is fairly simple to install the SignaLink, it is

possible to DAMAGE YOUR RADIO or the SignaLink by incorrectly installing it!

IMPORTANT NOTES

 SignaLink USB Users - The SignaLink USB is always powered by the computer's USB jack. When installing the jumpers

for the SignaLink USB using the settings shown here and in our other documentation, please disregard the PWR jumper

(do NOT install it!). All other jumper settings are the same. Note that if you mistakenly install the PWR jumper, it will

make no difference in the operation of the unit as this pin is not internally connected.

 Select The Correct Diagram - When viewing the jumper settings below, BE CERTAIN THAT YOU ARE LOOKING

AT THE CORRECT DIAGRAM for the radio connector that you

will be using. For any given radio, there are likely to be different

jumper settings for the Mic, Data and Accessory Port connectors.

 RJ-45 Mic Connectors - There is a lack of standardization in the way

that radio manufacturers number their RJ-45 mic connectors. We

have numbered our connector according to the dominant industry

standard as shown to the right. Icom and Radio Shack also follow this

standard, but Kenwood, Yaesu and some others do not. You need to

be very careful to determine how your mic connector is numbered to

avoid reversing connections!

 PTT - You should verify in your radio manual that the radio PTT

requirements do not exceed the specifications of the SignaLink keying

circuit (please refer to the SignaLink manual) and that the PTT line is

“Grounded” to make the radio transmit. If your radio exceeds the

specifications listed or requires some other keying arrangement, then

please contact our Technical Support Staff for suggestions.

 POWER - The SignaLink USB is always powered by the computer's USB jack. When installing the jumpers for the

SignaLink USB, please disregard the PWR jumper. All other jumper settings are the same. If you mistakenly install the

PWR jumper, everything is OK as this pin is NOT connected inside the unit.

 Jumper Wire Color - The jumper wires in the diagrams below are shown in color for illustrative purposes only. The color

of the wires means nothing - they're just easier to see! The actual jumper wires that are included with the SignaLink are all

the same color and can be used to jumper any signal.

Note that the SignaLink USB is always powered by the computer, so you can disregard the PWR jumper when installing

this unit.

 RECEIVE AUDIO / SPEAKER AUDIO - Receive Audio is available on the Mic, Data, and Accessory Port connectors

of most radios. If Receive Audio is not shown in the jumper settings for your radio, then consult your radio manual to see

if it is available. If it is not, then you will need to connect a mono cable between your radio's External Speaker or

headphone jack, and the "Speaker" jack on the back of the SignaLink. See the SignaLink Installation Manual for details.

1 2 3 4 5 6 ... 14 15

Inhaltsverzeichnis

Seite 1 - Interface Listing

TGR-SL-USB

Seite 2

TEN-TEC 5-Pin DIN Accessory Connector - TGR-SL-CAB5PD Radio Models Pin-out Notes JP-1 Argonaut V Jupiter Omni VII Pegasus Check the SLMOD5PD J

Seite 3

YAESU RJ-11 Mic Connector - TGR-SL-CABRJ1 Radio Models Pin-out Notes JP-1 FT-90/90R FT-100** FT-1500M FT-1802 / 1900R FT-2600 FT-2800M FT-2900R FT-780

Seite 4

YAESU 5-Pin DIN Packet Connector - TGR-SL-CAB5PD Radio Models Pin-out Notes JP-1 FT-920* FT-1000*** FT-1000D*** FT-1000MP## FT-1000MPMKV** FT-1000MPMK

Seite 5

PLUG-N-PLAY MODULES SLMOD6PM SLMOD8PD SLMOD13I SLMOD13K SLMODK3 ICOM IC-207H IC-208H IC-2720H IC-2800 IC-2820 IC-703 IC-706MKIIG IC-746PRO IC-7000 IC

Seite 6

PLUG-N-PLAY MODULES SLMOD5PD SLMOD8RI SLMOD8RK SLMOD8RY YAESU FT-920 FT-1000MP FT-1000MPMKV FT-1000MPMKV Field FT-2000 FTDX-5000/D/MP FTDX-9000/D/MP

Seite 7

Plug-N-Play Module Installation Instructions The installation of the of the Plug & Play jumper modules is very simply, but you need to be careful

Seite 8 - KENWOOD

SELECT A MANUFACTURER NOTE: Please read the "Important Notes" above BEFORE you select your jumper settings. This will save time and may he

Seite 9

DRAKE 4-Pin Round Mic Connector - TGR-SL-CAB4R Radio Models Pin-out Notes JP-1 TR-7 TR-22 TR-33 UV-3 Pin 1 – Mic Input Pin 2 – PTT Pin 3 – N/C Pi

Seite 10

ICOM 4-Pin Round Mic Connector - TGR-SL-CAB4R Radio Models Pin-out Notes JP-1 IC-22 IC-202/215/245/280 IC-402 IC-502/551 IC-701 Pin 1 – Mic Input

Seite 11

ICOM 6-Pin Mini DIN Data Port Connector - TGR-SL-CAB6PM Radio Models Pin-out Notes JP-1 IC-207H/208H IC-2720H IC-2800**** IC-2820 IC-703 IC-706MKIIG*

Seite 12 - YAESU FT-847 ONLY

ICOM 8-Pin DIN Accessory Port Connector - TGR-SL-CAB8PD Radio Models Pin-out Notes JP-1 IC-275A IC-575A/H IC-707 IC-725/726/728/729 IC-735/736/737/738

Seite 13 - PLUG-N-PLAY MODULES

KENWOOD 4-Pin Round Mic Connector - TGR-SL-CAB4R Radio Models Pin-out Notes JP-1 TR-7200A TR-7400A TR-7500 TS-120S/130S/180S TS-511S/520/530 TS-600 TS

Seite 14

KENWOOD 6-Pin Mini DIN Port Connector - TGR-SL-CAB6PM Radio Models Pin-out Notes JP-1 TM-251/255 TM-271**/271A** TM-451/455 TM-D700/D700A TM-D710/710A

Seite 15

MIDLAND 4-Pin Round Mic Connector - TGR-SL-CAB4R Radio Models Pin-out Notes JP-1 13-510 Pin 1 – Mic Input Pin 2 – GND Pin 3 – N/C Pin 4 – PTT

Kommentare zu diesen Handbüchern

Keine Kommentare

Alinco DR-592T Installationshandbuch

Stöbern Sie online oder laden Sie Installationshandbuch nach Satellitenantennen Alinco DR-592T herunter. Alinco DR-592T Installation manual [en] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern